Skip to main content

Biographies

Read the information below to learn about the group members:

 Advisor:
Dr. Tein-Min Tan
email: tan@drexel.edu




Dr. Tan is an associate professor for Mechanical Engineering and Mechanics at Drexel University. His research interests include mechanics of composites, computational mechanics and finite-elements methods, and structural dynamics.


Members:
Thomas Austin
Mechanical Engineering Major
email: tra43@drexel.edu



Thomas spent most of his life in Skillman, New Jersey. Outside of engineering, Thomas enjoys playing soccer, music, and running.


David Haruch
Mechanical Engineering Major
email: djh367@drexel.edu

David is from Media, Pennsylvania. In addition to engineering, his interests include mountain biking, playing guitar, and 80s/90s metal music.






Drew Jacobs
Mechanical Engineering Major
email: daj62@drexel.edu



Drew is from Media, Pennsylvania. As well as engineering, Drew is in the Alpha Pi Lambda Fraternity and enjoys playing golf and hanging out with friends.
Chris Kierce
Mechanical Engineering Major
email: ck683@drexel.edu



Chris is from Cohasset, Massachusetts. Outside of engineering, Chris' interests are auto racing, cars, and baseball.


Lauren Lugones
Mechanical Engineering Major
email: lml355@drexel.edu



Lauren is from Miami, Florida. Her interests outside of engineering include cars and PC gaming.

Comments

Post a Comment

Popular posts from this blog

Week 6

Last week (Week 5), the group focused on preparing for the manufacturing of the pedal box. In order to do this, the design was made lighter and the group used the Finite Element Analysis (FEA) tool on Solidworks to see how well the material would hold up under force. This week (Week 6), the group finalized the preparations for manufacturing and sent parts to be created. In order to prepare for manufacturing, the group finalized the computer aided design of the pedal box, which can be seen below. In order to finalize this design, David added the real model of the balance bar to the assembly and added ball bearings to the pedals. These make the overall design more realistic when it comes to how the pedal box is actually going to function. Balance Bar (Left) || Ball Bearing (Bottom Right) Additionally, one problem that the group ran into was the forces on the brake pedal. It was determined that the screws holding the balance bar and master cylinder systems were under too much
Post a Comment
Read more

Week 5

Last week (Week 4), the group dove into the modelling of the pedal box, in addition to working on the Finite Element Analysis (FEA) which resulted from the design. Specifically, the FEA of the brake pedal was tested to see the strength of the material, and the pedal box slide was incorporated into the overall design. For this week (Week 5), more analysis was done on the pedal box as the group gets ready for its manufacturing. The final design of the pedal box is as such: To start off, the group focused on making the pedal box as light as possible. In order to achieve this goal this week, much of the group's attention was directed towards the throttle pedal. Last week (Week 4), David and Lauren both worked to find the appropriate thickness of the throttle pedal. While this is great for the overall design, it then makes the system marginally heavier. In order to counteract this, David put holes in the design and thinned the width of the throttle. This makes the overall system
Post a Comment
Read more

Week 9

Last week (Week 8), the group focused on the machining of the throttle pedal, in addition to ordering the material for the adjustable slides. This week (week 9), the group manufactured the adjustable slides for the machine shop. Before thye physically manufactured the product, the overall design was updated by a senior member of Formula SAE. This design can be seen below. A small edge of metal was added to the side of the adjustable slide in order to absorb more force from the pedal box. Additionally, more metal was added beneath the bolts connecting to the chassis in order to add more support to the overall system. A photo of the product (halfway through manufacturing), as well as a video of the manufacturing, can be seen below:         Lauren made spacers for the gap between the pedals and pressed the bearings for the brake pedals. In order to do this, she first had to bore the hole for the brake pedal bearing. A video of machining this week can be seen below:
Post a Comment
Read more